Best Bed Racks for 2024–2026 Toyota Tacoma: 5 Picks That Fit the New Deck Rails

Rough Country's full-height rack is the pick because it was made for this truck rather than carried over. The Amazon listing names the 2024–2025 Tacoma, and Rough Country's product page (part 73119, configurable) covers 2024–2026 2WD and 4WD trucks. It is powder-coated aluminum, which keeps the weight down on a midsize truck, and it comes with molded end caps and T-slot covers. Rough Country rates it at 750 lb static and 400 lb dynamic, both published, which makes it easy to plan a rooftop tent and gear against the moving figure.

The fitment notes are short and firm. Rough Country says the rack only fits models with the 5 ft bed and does not fit vehicles equipped with a bed cover. That rules out XtraCab and long-bed Double Cab owners and anyone who wants a tonneau under it. Rough Country's page lists it from $589.95 with a lifetime warranty, but doesn't give the rack's height or weight, so check the configured option before ordering. If you want a cover as well, Rough Country's 73141 rack ($499.95) has the same ratings and is built to work with its powered retractable cover.

Mid-height is the sweet spot for a rooftop tent on a midsize truck, and this OTHOWE rack is one of the few budget listings that names the 2024 and 2025 Tacoma specifically. The title gives an 18 in height and says it is for trucks with factory bed rails and without a tonneau cover. At 18 in the tent sits near the roofline, where the cab takes some of the wind and the truck stays easier to park than with a full-height rack.

The spec sheet is thin. OTHOWE's own site wouldn't load for us, and the listing title doesn't give separate static and dynamic ratings, so read the capacity on the listing before you plan a sleeping load. Because it clamps to the factory rails, a base SR without the deck rail system will need the rails first. Confirm which bed length the listing covers, since most 4th-gen racks target the 5 ft bed. For a tent-height rack that was built around the new truck, it is a sensible lower-cost alternative to the Rough Country.

An adjustable rack is useful on the 4th-gen Tacoma because so few racks name the 6 ft bed. YZONA's store lists this 16.8–25 in rack as a universal design rated at 1,000 lb, at $499.99, and the Amazon title names the Tacoma among a list of trucks. The height range covers a low setting for daily driving and a tall one for room under a tent. On YZONA's Tundra page for the same height range, the rack is described as steel with a textured powder coat, rated 1,000 lb stationary and 500 lb in motion, with a no-drill snap-on mount and cover compatibility.

The universal fit is the reason for the confirm note. The listing isn't specific to the 2024+ Tacoma, and the 4th-gen rail channel differs from the older truck's, so ask the seller whether the clamps suit your deck rails and which bed lengths the hoop spacing covers. Also ask which load figure applies while driving before you carry a tent on it. If those answers come back right, it is one of the few ways to get an adjustable tent rack on a 6 ft 4th-gen bed.

A low rack is the right tool when the load is bikes, kayaks, boards or a basket. This YZONA rack is listed at 13.3 in for the 2016–2025 Tacoma with bed rails, with two LED lights and a 1,000 lb figure in the title. At that height it stays well below the cab roof, which keeps wind noise and overall height down and leaves the cab roof free if you later add a roof rack for a second set of bars.

The title's year range is what needs checking. It covers the 2016–2023 Tacoma and the 4th-gen truck in one listing, and the two beds use different rail channels, so confirm with the seller that the clamps are the version made for the 2024+ rail. The 1,000 lb figure isn't labeled static or dynamic, and at 13.3 in a rooftop tent would sit just above the bed rails with little room to reach underneath, so treat it as a cargo rack unless the seller's numbers support more.

The SUORTO rack is a simple ladder-style rack with crossbars and two LED lights, listed for the 2016–2025 Tacoma and 2020–2025 Jeep Gladiator with bed rails. It is aimed at the everyday jobs a Tacoma bed rack does most: ladders, lumber, kayaks and bikes, with the bed below still usable. Because it grips the factory bed rails, it avoids drilling into the composite bed.

It is on the list as a budget option, and the confirm note matters. The title covers both Tacoma generations in one listing, and the 4th-gen rail channel differs from the 2016–2023 truck's, so ask the seller whether the clamps are made for the 2024+ rail. The title also doesn't state a load rating or height, so read those on the listing before loading anything heavy, and don't plan a sleeping load on it without a published static figure. If you need a tent rack, the Rough Country or OTHOWE picks are better starting points.